Ciscomotors C-Max Betriebsanleitung

SNAP 100MAINTENANCE MANUALAll information in this publication is based the lates product information available at the time ofapproval for printing.CIS

Pag. 104. STORAGEExtended storage such as for winter, requires that you take certain steps to reduce the effects ofdeterioration from nonuse of your S

Pag. 115. SPARE PARTS & EQUIPMENT5.1 SPARE PARTSCOD. DESCRIZIONE000001.0SPARK PLUG CUP000002.0SHAFT SPARK PLUG000003.0CARBON FIBER COOLING AIR DUC

Pag.125.2 EQUIPMENTSCOD DESCRIPTION100.200FLYWHEEL CLUTCH100.201FLYWHEEL BELL CLUTCH100.300SOCKETS HEX 17 m/m100.301SOCKETS HEX 11 m/m100.302SOCKETS H

Pag.136. DISASSEMBLY/ASSEMBLYWARNINGModification of the motor, or removall of original equipment may make the motor unsafe.6.1 DISASSEMBLY CARBURETTOR

Pag.146.2 DISASSEMBLY TERMICAL GROUPThis section covers maintenance of the cylinder and piston. These service can be done with theengine installed in

Pag.157. Pull the exhaust with resolution (Fig.8)* Apply silicon gasket higt temperature.Fig.8Fig.98. Remove the 4 cylinder head bolts and nuts(Fig.9)

Pag.16DISASSEMBLY PISTONFig.1110. Remove the piston pin clips using a pair ofneedle-nose pliers (Fig.11)11. Press the piston pin out of the piston and

Pag.17DecarbonizingCOMBUSTION CHAMBERRemove the carbon deposits from the combustion chamber. Clean the head gasket surface of anygasket materialCAUTIO

Pag18INSTALLATION CYLINDER6. Install the new cylinder gasket7. Allign each ring and gap with the piston ringpins in the ring groves (Fig.16)Fig. 168.

Pag. 19INSTALLATION CYLINDER HEAD1. Install the new cylinder head gasket o-ring (Fig.10)2. Install the cylinder head and nuts (Fig.9 ), tighten the nu

INDEX Pag.21. OPERATING INSTRUCTIONS Pag. 3• 1.1 Basic operation Pag. 42. SPECIFICATIONS Pag. 6• 2.1 Engine installation on chassis Pag. 6• 2.2 Tec

Pag. 206.3 DISASSEMBLY/ASSEMBLY STARTERFig.181. Remove the air duct see the chapter 6.22. Remove 4 screw (Fig.18)3. Remove the bolt (Fig.19)4. Remove

Pag. 216.4 DISASSEMBLY/ ASSEMBLY SILENCER1. Remove the exhaust like chapter 6.22. Remove the 3 bolts and cap screw fixingsilencer (Fig,.22)3. Remove t

Pag.226.5 DISASSEMBLY/ASSEMBLY SPONGE FILTERFig.231. Unscrew the filter band (fig.23)2. Remove the airbox from the motor3. Remove 4 screw (Fig.24)4. R

Pag.237. CARBURATION REGULATIONFig.261. Regulation throttle cable2. Regulation Min. gasoline3. Regulation Max gasolineStandard regulationIn case of pr

Pag.248. TROUBLESHOOTING1. THE ENGENE DOES NOT START OR IS HARD TO STARTCHECK POSSIBLE CAUSES SOLUTIONNo fuel in tank Fill tank per fuelingClogget fue

Pag.253. THE ENGINE VIBRATES EXCESSIVECHECK POSSIBLE CAUSES SOLUTIONExessive wear, holder rubber Repalce (Max 70 Sh)Silent-block engineProp out of bal

Pag.31. OPERATING INSTRUCTIONSFUEL• Snap 100 has a two-stroke engine thatrequires a gasoline-oil mixture.• Use gasoline with a pump octanenumber of

Pag. 41.1 BASIC OPERATION• In the 2-stroke motors like the Snap100, is of absolute importance the correctedcarburation to avoid seizure to the piston

Pag. 5Fig.2

Pag. 62. SPECIFICATIONS2.1 ENGINE INSTALLATION ON CHASSISFig.31. Engine stop connector 2. Throttle cable 3. Propeller4. Support engine 5. Manual start

Pag.72.2 TECHICALS CHARATTERISTICSMotor SNAP 100SType 2 times cooled to airDisposition cylinder Monocylinder verticalBore max 51mmStroke max 47mmDispl

Pag. 83. MAINTENANCE3.1 GENERAL SERVICE INFORMATION:• To wear gloves and glances when you make the maintenance;• Do not perform maintenance while en

Pag. 93.3 MAINTENANCE SCHEDULEFREQUENCY INSPECT REPLACEBefore and after each use All screw nuts, bolts correctlytigthen, silent-block in.Every 100 hou